Forschungsbericht 2009

M-22 Werkstoffphysik und -technologie

Forschungsprojekte

• E.5-06.2006.01 Thermomechanische Behandlung von mikrolegierten Magnesiumlegierungen
• E.5-06.2006.02 Universelle Kornfeinung in Magnesiumlegierungen durch keramische Partikel: Modellierung und Processing
• E.5-06.2006.03 Texturentwicklung bei der Hochtemperaturverformung von neuartigen Niob-reichen g-TiAl-Legierungen
• E.5-06.2006.04 Thermomechanische Behandlung von mikrolegierten Magnesiumlegierungen
• E.5-06.2006.05 Characterization and optimization of mechanical properties of massively transformed Ti-46Al-9Nb sheet material

Kooperationen

• AB Technische Keramik der TUHH
• DaimlerChrysler Forschungszentrum, Ulm
• Dornier Friedrichshafen
• GKSS-Forschungszentrum
• Gränges Technology Centre, Finspong, Schweden
• IKTS Dresden
• Inst. f. Metallkunde der Universität Stuttgart
• Institut für Gesteinshüttenkunde, Leoben
• Kyoto Institute of Technology
• Kyoto National University, Japan
• Los Alamos National Laboratory, NM, USA
• MPI Düsseldorf
• Plansee AG, Reutte i. Tirol
• SLV München
• Slowakische Akademie der Wissenschaften Kosice
• Swedish Institute for Metals Research (SIMR) Stockholm
• TU St. Petersburg
• Technische Fakultät, Universität Kiel
• Universidade Federal de Sao Carlos, Brasilien
• University of Limerick
• Universität Bayreuth
• Universität Grenoble, Frankreich
• Universität Münster
• Universität Rosario, Argentinien
• Universität der Bundeswehr Hamburg
• Volkswagen AG, Wolfsburg
• Yokohama National University, Japan

Publikationen

Veröffentlichungen

• 5-06.201V
  

  M. Herrmann, C. Schubert, A. Rendtel, H. Hübner,""Silicon Nitride/Silicon Carbide Nanocomposite Materials: I, Fabrication and Mechanical Properties at Room Temperature", J. Am. Ceram. Soc., 81 (1998),

  pp. 1095-1108".

• 5-06.202V
  

  A. Rendtel, H. Hübner, M. Herrmann, C. Schubert,""Silicon Nitride/Silicon Carbide Nanocomposite Materials: II, Hot Strength, Creep, and Oxidations Resistance", J. Am. Ceram. Soc., 81 (1998), pp. 1109-1120".

• 5-06.203V
  

  E. Müller Ch. Oestreich, U. Popp, R. Herbig, G. Michel, A. Rendtel,""The Influence of the Preparation Conditions of Nanocrystalline Zirconia on Powder Processing and Ceramic Properties", Polish Ceramic Bulletin 15, Polish Academy of Science ¿ Kraków Division, Papers of the Commission on Ceramic Science, Polish Ceramic Society ", Ceramics 53 (1997), p. 211".

• 5-06.204V
  

  E. Müller, Ch. Oestreich, U. Popp, G. Michel, A.Rendtel,""Investigations of nanocrystalline ceramics and powders by TEM, AFM and plasticity measurements", Fresenius J Anal Chem 361:(1998), pp. 594-597".

• 5-06.205V
  

  R. Lebensohn, H. Uhlenhut, C. Hartig, H. Mecking,""Plastic Flow of Gamma-TiAl-Based Polysynthetically Twinned Crystals: Micromechanical Modeling and Experimental Validation", Acta mater. 46 (1998), pp. 4701-4709".

• 5-06.206V
  

  A. Rendtel, H. Hübner,""Calculation of the Shape Change of Refractory Linings Using the Creep Properties of the Employed Materials", Stahl und Eisen SPECIAL, Sept. 1998, pp. 135-139".

• 5-06.207V
  

  Bartels, Ch. Hartig, St. Willems, H. Uhlenhut,"" Influence of the Deformation Conditions on the Texture Evolution in Gamma-TiAl¿, Mat. Sci. Eng. A 239-240 (1997), pp. 14-22".

• 5-06.208V
  

  A. Bartels, H. Uhlenhut,""Anisotropy of plastic flow in strongly textured Gamma-TiAl-based alloys¿, Intermetallics 6 (1998), pp. 685-688".

• 5-06.209V
  

  T. Klassen, R. Günther, B. Dickau, F. Gärtner, A. Bartels, R. Bormann, H. Mecking,""Processing and Properties of Intermetallic/Ceramic Composites with Interpenetrating Microstructure¿, J. Am. Ceram. Soc. 81(1998), pp. 2504-506".

• 5-06.210V
  

  H. Mecking und A. Bartel,""Festigkeit und Duktilität von intermetallischen Aluminiden¿ in: Danzer und M. Pohl (Hrsg.): Proc. ¿Gefüge und Bruch¿, Leoben, 20.-22. März 1996, pp".

• 5-06.211V
  

  G. Bermig, A. Bartels, H. Mecking, A. Oscarsson, B.- Hutchinson,""Entwicklung der Mikrostruktur und der Textur von Aluminiumlegierungen beim Flachstauchen im Hochtemperaturbereich¿ in: ¿Werkstoffwoche ¿96, Simulation, Modellierung, Informationssysteme¿, DGM Informationsgesellschaft 1997, pp. 119-123".

• 5-06.212V
  

  B. Commentz,""Residual Strain in Fe-Cu-Composites, Part 1: Experimental¿, in: H.-G. Brokmeier, B. Witassek (Hrsg.): ¿TEX-2-Experimental Reports 1996¿, GKSS-Publikation GKSS 97/E/72, Geesthacht (1997), pp. 39-42".

• 5-06.213V
  

  W. Oelerich, S. Willems, A. Bartels, H. Mecking,""Texturentwicklung von Ti58a%Cr während der thermomechanischen Behandlung¿ Proc. der Werkstoffwoche 1996, Symposium 7, (1996), pp. 429-434".

• 5-06.214V
  

  G. Bermig, A. Bartels, H. Mecking,""Analysis of Flow Behaviour and Texture Evolution of a Particle Hardened Aluminum Alloy in Plane Strain Deformation¿, in: Proc. ICAA5, Grenoble, July 1-5, 1996, pp. 429-434".

• 5-06.215V
  

  St. Willems, H. Uhlenhut, A. Bartels, H. Mecking,""Thermal and Athermal Deformation Processes in Equiaxed Ti-48Al-2Cr between Room Temperature and 600°C¿, in: W.O. Soboyejo, T.S. Sritvatsan, H.L. Fraser (Hrsg.): ¿Deformation and Fracture of Ordered Intermetallic Materials¿, TMS, Warrendale, Pennsylvania1997, pp. 207-215".

• 5-06.216V
  

  A. Bartels, H. Clemens, C. Hartig, H. Mecking,""Mechanical Anisotropy in Sheets of Gamma-TiAl Alloys¿ in: C. Koch, C.T. Liu, N. Stoloff, A. Wanner (Hrsg.:) "High-Temperature Ordered Intermetallic Alloys-VII¿; MRS Vol. 460 (1997), pp. 141-146".

• 5-06.217V
  

  G. Bermig, A. Bartels, H. Mecking, Y. Estrin,""A Unique Description of Steady State Deformation of Al and Al-Mg Alloys¿,

  Mater. Sci. Eng. A234-236 (1997), pp. 904-907".

• 5-06.218V
  

  R. Gerling, A. Bartels, H. Clemens, M. Oehring and F.-P. Schimansky,""Properties of two-phase intermetallic (Ti,Nb)3(Al,Si) + (Ti,Nb)5(Si,Al)3 P/M bulk and sheet material¿, Acta. mater. 45 (1997), pp. 4057-4066".

• 5-06.219V
  

  R. Gerling, A. Bartels, H. Clemens, M. Oehring and F.-P. Schimansky,""Properties of two-phase intermetallic (Ti,Nb)3(Al,Si) + (Ti,Nb)5(Si,Al)3 P/M bulk and sheet material¿, Acta. mater. 45 (1997), pp. 4057-4066".

• 5-06.220V
  

  C. Michaelsen, P. Ricardo, D. Anders, M. Schuster, J. Schilling, and H. Göbel, "Improved graded multilayer mirrors for XRD applications", Adv. X-ray Anal. 42, 308 (2000).

• 5-06.221V
  

  B. Commentz, Ch. Hartig, H. Mecking: "Micromechanical interaction in two-phase iron-copper polycrystals", Computational Materials Science, 16 (1999) p.237-247

• 5-06.222V
  

  M. Schuster, H. Göbel, L. Brügemann, D. Bahr, F. Burgäzy, C. Michaelsen, M. Störmer, P. Ricardo, R. Dietsch, T. Holz, and H. Mai, "Laterally graded multilayer optics for x-ray analysis", Proc. SPIE 3767, 183 (1999).

• 5-06.223V
  

  M. Koeppe, Ch. Hartig, H. Mecking: "Anomalies of the plastic yield stress in the intermetallic compound Fe-30at.%Al", Intermetallics 7 (1999), p.415-422

• 5-06.224V
  

  H. Hübner, P. Rendtel und A. Rendtel: Si3N4/SiC-Nanocomposite für Höchsttempera-turanwendungen, in J. Heinrich, G. Ziegler, W. Hermel und H. Riedel (Hrsg.): Kera-mik/Werkstoffwoche 98, Band VII, Symposium 9, Wiley - VCH 1999, pp. 483- 488.

• 5-06.225V
  

  P. Rendtel, A. Rendtel, H. Hübner, H. Klemm and M. Herrmann: Effect of Long-Term Oxidation on Creep and Failure of Si3N4 and Si3N4/SiC Nanocomposites, J. Eur. Ceram. Soc. 19, No. 1(1999)217-226.

• 5-06.226V
  

  V.C. Pandolfelli & J.A. Rodrigues, A.P.M. Menegazzo, A. Rendtel & H. Hübner: High Temperature Mechanical Tests as a Tool for the Microstructural Design and Evaluation of Advanced Castables, Refractories Application, January 1999.

• 5-06.227V
  

  A. Rendtel, D. Bellmann, R. Kampmann und H. Hübner: Kriechverhalten und Kriech-schädigung von Si3N4/SiC-Nanocompositen unter Zugbelastung, in K. Schulte und K. H. Kainer (Hrsg.): Verbundstoffe und Werkstoffverbunde, Wiley-VCH 1999, pp. 411-416

• 5-06.228V
  

  M. Sternitzke, T. Zhang, F. Meschke und H. Hübner: Kriechverhalten von gesinterten Aluminiumoxid/Siliziumcarbid Nanokomposit-Keramiken. in K. Schulte und K. H. Kainer (Hrsg.): Verbundwerkstoffe und Werkstoffverbunde, Wiley-VCH 1999, pp. 313-318

• 5-06.229V
  

  M. Sternitzke, T. Zhang, F. Meschke and H. Hübner: Creep behavior of pressureless sintered alumina/ silicon carbide nanocomposites, Proc. EUROMAT 99, München 10/1999.

• 5-06.230V
  

  A. Rendtel and H. Hübner: Creep Resistant Silicon Nitride Ceramics - Approaches of Microstructural Design, Ceram. Eng. Sci. Proc. 21, No. 3-4(2000), in press.

• 5-06.231V
  

  T. Klassen, M. Oehring und R. Bormann, "Microscopic Mechanisms of Metastable Phase Formation During Ball Milling of Intermetallic TiAl Phases", Acta mater. 45 (1997), 3935

• 5-06.232V
  

  Z.Q. Guan, Th. Pfullmann, M. Oehring und R. Bormann, "Phase Formation During Ball Milling and Subsequent Thermal Decomposition of Ti-Al-Si Powder Blends", J. Alloys and Compounds 252 (1997), 245

• 5-06.233V
  

  T. Klassen, R. Günther, B. Dickau, A. Bartels, R. Bormann und H. Mecking, "Processing and Characterization of Novel Intermetallic/Ceramic Composites", Mater. Science Forum 269-272 (1998), 37

• 5-06.234V
  

  T. Klassen, W. Oelerich, K. Zeng, R. Bormann und J. Huot, "Nanocrystalline Mg-based Alloys for Hydrogen Storage", in: "Magnesium Alloys and their Applications", Hrsg. B.L. Mordike und K.U. Kainer, Werkstoff-Informationsgesellschaft mbH, Frankfurt (1998), 307 und GKSS 98/E/9

• 5-06.235V
  

  T. Klassen, R. Günther, B. Dickau, F. Gärtner, A. Bartels, R. Bormann und H. Mecking, "Processing and Properties of Intermetallic/Ceramic Composites with Interpenetrating Microstructure", J. Amer. Ceram. Soc. 81 (1998) 2504

• 5-06.236V
  

  R. Günther, T. Klassen, B. Dickau, A. Bartels und R. Bormann, "Herstellung und Eigenschaften intermetallischer keramischer Verbundwerkstoffe", Proc., "Werkstoffwoche '98, Band VII: Keramik/Simulation Keramik", Wiley-VCH, 681-686, 1998

• 5-06.237V
  

  R. Günther, T. Klassen, A. Bartels und R. Bormann, "Neuartige Nb- und Ti-metallverstärkte Al2O3-Verbundwerkstoffe: Herstellung, Eigenschaften und potentielle Anwendungen", Hrsg. Prof. Dr. J. Kriegmann, Fachverlag Deutscher Wirtschaftsdienst GmbH, in Druck

• 5-06.238V
  

  K. Zeng, T. Klassen, W. Oelerich und R. Bormann, "Critical Assessment and Thermodynamic Modeling of the Mg-H System", Intl. J. Hydrogen Energy 24 (1999), 989-1004

• 5-06.239V
  

  K. Zeng, T. Klassen, W. Oelerich und R. Bormann, "Thermodynamics of the Ni-H System", J. Alloys and Compounds 283 (1999), 151-161

• 5-06.240V
  

  K. Zeng, T. Klassen, W. Oelerich und R. Bormann, "Thermodynamics Analysis of the Hydriding Process of Mg-Ni Alloys", J. Alloys and Compounds 283 (1999), 213-224

• 5-06.241V
  

  R. Bohn, G. Fanta, R. Günther, B. Dickau, T. Klassen, F. Gärtner, A. Bartels und R. Bormann, "Mechanical Properties of Intermetallic/Ceramic Composites Prepared by High Energy Milling", Proc. ISMANAM '98, Hrsg. A. Calka, D. Wexler, Journal of metastable and nanocrystalline materials 2-6 (1999) and Mater. Science Forum, 312-314, Trans-Tech. Publications, Switzerland (1999), 575-580

• 5-06.242V
  

  R. Bohn, G. Fanta und R. Bormann, "Improved hot workability of g-TiAl-based composites by grain refinement", Proc. EUROMAT '99, in Druck

• 5-06.243V
  

  W. Oelerich, T. Klassen und R. Bormann, "Nanocrystalline Metal Hydrides for Hydrogen Storage", Proc. EUROMAT '99, in Druck

• 5-06.244V
  

  R. Günther, T. Klassen, B. Dickau, F. Gärtner, A. Bartels und R. Bormann, "Preparation and Properties of novel Nb- and Ti-based metal reinforced Alumina Composites with interpenetrating Microstructure", Proc. EUROMAT '99, in Druck

• 5-06.245V
  

  F. Gärtner, R. Bormann, T. Klassen, H. Kreye, N. Mitra, "Nanocrystalline Composites for Thermal Spray Applications", Keynote Lecture, International Conference on Metastable, Mechanically Alloyed and Nanocrystalline Materials, ISMANAM 99, held in Dresden, Germany, August 29 - September 03, 1999, to be published in Materials Science Forum.

• 5-06.246V
  

  F. Gärtner, H. Kreye, R. Bormann, T. Klassen, "Titanium Carbide Based Cermets for Thermal Spray Applications", International Congress on Advanced Materials and Processes, EUROMAT 99, held in München, Germany, September 27 - September 30, 1999, Volume 11, Surface Engineering (ed.: H. Dimigen), WILEY-VCH, Weinheim, Germany, 2000

• 5-06.247V
  

  F. Gärtner, H. Kreye, V. Borck and W. Krömmer, "The Effect of Oxidation on Microstructure and Properties of TiC-Based Cermet Coatings" , Proc. ITSC 2000, held in Montreal, Canada, 8 - 11-May 2000 (ed.: C.C. Berndt), ASM International, 2000.

• 5-06.248V
  

  W. Schillinger, A. Bartels, K. Kishida: "Mechanical Anisotropy in Textured Sheets of g-TiAl"; in: D.G. Morris, S. Naka, P. Caron (Eds.), Intermetallics and Superalloys, Euromat Vol. 10, Wiley-VCH, (Weinheim, 2000), pp. 378

• 5-06.350V
  

  Liss, K.-D., A. Bartels, H. Clemens, S. Bystrzanowski, A. Stark, T. Buslaps, F.P. Schimansky, R. Gerling, and A. Schreyer, A Study of Recrystallization and Phase Transitions in Intermetallic Titanium Aluminides by In-Situ High-Energy X-Ray Diffraction. Materials Science Forum 2007. 539-543: p. 1519-1524.

• 5-06.351V
  

  Stark, A., A. Bartels, R. Gerling, F.P. Schimansky, and H. Clemens, Microstructure and Texture Formation during Hot Rolling of Niobium-Rich g TiAl Alloys with Different Carbon Contents. Advanced Engineering Materials, 2006. 8(11): p. 10

• 5-06.352V
  

  Schillinger, W., A. Bartels, R. Gerling, F.P. Schimansky, and H. Clemens, Texture evolution of the gamma- and the alpha/alpha(2)-phase during hot rolling of gamma-TiAl based alloys. Intermetallics, 2006. 14(3): p. 336-347

• 5-06.353V
  

  Liss, K.-D., A. Bartels, H. Clemens, S. Bystrzanowski, A. Stark, T. Buslaps, F.-P. Schimansky, R. Gerling, C. Scheu, and A. Schreyer, Recrystallization and phase transitions in a γ-TiAl-based alloy as observed by ex situ and situ high-energy X-ray diffraction. Acta Materialia, 2006. 54: p. 3721-3735

• 5-06.354V
  

  Laser, T., M.R. Nurnberg, A. Janz, C. Hartig, D. Letzig, R. Schmid-Fetzer, and R. Bormann, The influence of manganese on the microstructure and mechanical properties of AZ31 gravity die cast alloys. Acta Materialia, 2006. 54(11): p. 3033-3041

• 5-06.355V
  

  Laser, T., M.R. Nurnberg, C. Hartig, D. Letzig, and R. Bormann. The Influence of Calcium and Cerium Mischmetal on the Deformation Behavior of Mg-3Al-1Zn. in 7th International Conference on Magnesium Alloys and Their Applications. 2006. Dresden: WILEY-VCH

• 5-06.356V
  

  Günther, R., C. Hartig, and R. Bormann. Grain Refinement of AZ31 by (SiC)P: Theoretical Calculation and Experiment. in Magnesium: Proceedings of the 7th International Conference on Magnesium Alloys and Their Applications. 2006. Dresden: Wiley-VCH

• 5-06.357V
  

  Günther, R., C. Hartig, and R. Bormann, Grain refinement of AZ31 by (SiC)P: Theoretical calculation and experiment. Acta Materialia, 2006. 54(20): p. 5591-5597

• 5-06.358V
  

  Ebeling, T., C. Hartig, J. Bohlen, D. Letzig, and R. Bormann. Effects of Calcium on Texture Evolution and Plastic Anisotropy of the Magnesium Alloy AZ31. in Magnesium: Proceedings of the 7th International Conference on Magnesium Alloys and Their Applications. 2006. Dresden: Wiley-VCH

• 5-06.359V
  

  Clemens, H., A. Bartels, S. Bystrzanowski, H. Chladil, H. Leitner, G. Dehm, R. Gerling, and F.P. Schimansky, Grain refinement in gamma-TiAl-based alloys by solid state phase transformations. Intermetallics, 2006. 14(12): p. 1380-1385

• 5-06.360V
  

  Chladil, H.F., H. Clemens, H. Leitner, A. Bartels, R. Gerling, F.P. Schimansky, and S. Kremmer, Phase transformations in high niobium and carbon containing gamma-TiAl based alloys. Intermetallics, 2006. 14(10-11): p. 1194-1198

• 5-06.361V
  

  Hartig, C., A. Styczynski, F. Kaiser, and D. Letzig, Plastic anisotropy and texture evolution of rolled AZ31 magnesium alloys. Icotom 14: Textures of Materials, Pts 1and 2, 2005. 495-497: p. 1615-1620

• 5-06.362V
  

  Bystrzanowski, S., A. Bartels, H. Clemens, R. Gerling, F.-P. Schimansky, and G. Dehm, Creep Behavior and Microstructural Stability of Ti-46Al-9Nb with Different Microstructures, in Integrative and Interdisciplinary Aspects of Intermetallics. Materials Research Society Symposium Proceedings. 2005, Materials Research Society: Pittsburgh, PA, USA. p. 7.12.1-7.12.6

• 5-06.363V
  

  Bystrzanowski, S., A. Bartels, H. Clemens, R. Gerling, F.P. Schimansky, G. Dehm, and H. Kestler, Creep behaviour and related high temperature microstructural stability of Ti-46Al-9Nb sheet material. Intermetallics, 2005. 13: p. 515¿524

• 5-06.364V
  

  Bartels, A., S. Bystrzanowski, H. Chadil, H. Leitner, H. Clemens, R. Gerling, and F.-P. Schimansky, Massive Transformation in High Niobium Containing TiAl-Alloys, in Mater. Res. Soc. Symp. Proc. 2005, Materials Research Society. p. 5.48.1-5.48.6

• 5-06.365V
  

  Weller, M., H. Clemens, G. Dehm, A. Bartels, S. Bystrzanowski, R. Gerling, and E. Arzt, Mechanical sprectroscopy of a high-NB-bearing g-TiAl-based alloy with near-gamma and fully lamellar microstructure. Philosophical Magazine Letters, 2004. 84(6): p. 383-393

• 5-06.366V
  

  Styczynski, A., C. Hartig, J. Bohlen, and D. Letzig, Cold rolling textures in AZ31 wrought magnesium alloy. Scripta Materialia, 2004. 50: p. 943-947

• 5-06.367V
  

  Schillinger, W., A. Bartels, R. Gerling, and H. Clemens, Texture Formation during Hot- Rolling of g-TiAl, in Ti-2003 Science and Technologie, G. Lütjering and J. Albrecht, Editors. 2004, Wiley-VCH: Weinheim. p. 2385-2400

• 5-06.368V
  

  Clemens, H., F. Appel, A. Bartels, H. Bauer, R. Gerling, V. Günter, and H. Kestler, Processing and Application of Engineering g-TiAl Based Alloys, in Ti-2003 Science and Technologie, G. Lütjering and J. Albrecht, Editors. 2004, Wiley-VCH: Weinheim. p. 2123-2136

• 5-06.369V
  

  Bystrzanowski, S., A. Bartels, R. Gerling, F.P. Schimansky, H. Clemens, H. Kestler, G. Dehm, and M. Weller, Creep Properties and Texture of High Niobium Containing g-TiAl Sheet Material, in Ti-2003 Science and Technologie, G. Lütjering and J. Albrecht, Editors. 2004, Wiley-VCH: Weinheim. p. 2401-2408

• 5-06.370V
  

  Styczynski, A., Hartig, Ch., Bormann, R., Kaiser, P., Bohlen, J., Letzig, D. Texture Formation and Texture Modelling of AZ31 Magnesium Wrought Alloy. in 6th Int. Conf. "Magnesium Alloys and Their Applications". 2003

• 5-06.371V
  

  Laser, T., Hartig, Ch., Bormann, R., Bohlen, L., Letzig, D. . Dynamic Recrystallization of Mg 3AI 1Zn. in 6th Int. Conf. "Magnesium Alloys and Their Applications". 2003

• 5-06.372V
  

  Kaiser, F., D. Letzig, J. Bohlen, A. Styczynski, C. Hartig, and K.U. Kainer, Anisotropic properties of magnesium sheet AZ31, in Magnesium Alloys 2003, Pts 1 and 2. 2003. p. 315-320

• 5-06.373V
  

  Kaiser, F., J. Bohlen, D. Letzig, K.U. Kainer, A. Styczynski, and C. Hartig. Correlation of microstructure and mechanical properties of rolled magnesium sheet AZ31. in 2003 International Conference Magnesium Alloys and Their Applications. 2003. Wolfsburg, DE: Wiley-VCH, Weinheim

• 5-06.374V
  

  Kaiser, F., J. Bohlen, D. Letzig, K.U. Kainer, A. Styczynski, and C. Hartig, Influence of rolling conditions on the microstructure and mechanical properties of magnesium sheet AZ31. Advanced Engineering Materials, 2003. 5(12): p. 891-896

Dissertationen

• 5-06.006D
  

  Wolfgang Schröer: Plastisches Verhalten von Einkristallen aus intermetallischen Verbindungen auf der Basis Fe3 (Al,Si), 1992.

• 5-06.007D
  

  Harald Bosse:Untersuchungen der Konstitution und zum Verformungsverhalten von intermetallischen Phasen auf der Basis von Fe3 (Al,Si), 1992.

• 5-06.008D
  

  Joerg Seeger: Plastisches Fließen, Verfestigung und Gefügeentwicklung in zweiphasigen TiAl-Legierungen, 1993.

• 5-06.009D
  

  Wilson Acchar: Kriechverhalten plättchenverstärkter Siliciumnitridwerkstoffe, 1993.

• 5-06.010D
  

  Andreas Giese: Mechanisches Verhalten von ein- und vielkristallinem Aluminium und der Eisenbasislegierung INCOLY 800H unter Wechselbelastung, 1994.

• 5-06.011D
  

  Christian Wolf: Kriechverhalten von glasphasehaltigem Aluminiumoxid, 1994.

• 5-06.012D
  

  Dietmar Dunst ,"Hochtemperatur-Walztexturen und Koverformung der alpha- und beta-Phase zweiphasiger Titanbasislegierungen, 1996".

• 5-06.013D
  

  Stefan Willems ,"Reckalterungs- und Korngrößeneffekte bei plastischer Verformung von Ti-48Al-2Cr mit globularem Gefüge, 1998".

• 5-06.014D
  

  Claus von Minden,"Der Einfluß keramischer Verstärkungselemente auf die Kriechfestigkeit von Oxidkeramiken und von Glas, 1996".

• 5-06.015D
  

  Henning Uhlenhut: "Ursachen plastischer Anisotropie von Gamma-TiAl-Basislegierungen", Dissertation TU-Hamburg-Harburg, 1999, (Shaker Verlag, Aachen 1999), ISBN 3-8265-6222-4

• 5-06.016D
  

  Björn Commentz: "Plastische Verformung von zweiphasigen Eisen-Kupfer-Verbundwerkstoffen", Dissertation TU Hamburg-Harburg, 1999