Forschungsbericht 2006

5-08 Keramische Hochleistungswerkstoffe

Entwicklung und Anwendung Technischer Keramik einschließlich Sonderkeramiken

Kooperationen

• Dr. Tim Bastow, CSIRO Sydney, AUS
• Dr. Wayne Kaplan, Technion, Israel
• Kooperation mit diversen Industriepartnern
• Prof. Arturo Dominguez Rodriguez, University of Sevilla, Spain
• Prof. Bob McMeecking, UCSB, US
• Prof. Elazar Gutmanas, Technion, Israel
• Prof. Ken Sandhage, Ohio State University, US
• Prof. Kochi Niihara, Osaka University, Japan
• Prof. Martin Harmer, Lehigh University, US
• Prof. Mike Swain, University of Sydney, AUS
• Prof. Raj Bordia, University of Washington at Seattle, US
• Prof. Shin-ichi Hirano, Nagoya University, Japan
• Prof. Wolfgang Sigmund, University of Florida at Gainsville, US

Publikationen

Veröffentlichungen

• 5-08.030V
  M. Sindel, N. Claussen: Growth and Microstructural Development of Melt-Oxidation Derived Al2O3/Al-Base Composites, Proc. Brit. Ceram. Soc., 205-210,1990
• 5-08.031V
  S. Wu, N. Claussen: Fabrication of Low-Shrinkage Mullite-Zirconia Composites, Proc. Brit. Ceram. Soc., 91-95, 1990
• 5-08.032V
  N. Claussen, N. Travitzky: Mechanical Properties of Reaction-Bonded Silicon Nitride-Metal Composites, in: Processing of Ceramic and Metal Composites (Ed. H.Mostagaci), Pergamon, Toronto, 1989, 397.
• 5-08.033V
  N. Claussen, A.W. Urquhart: Directed Oxidation of Molten Metals, in: Concise Encyclopedia of Advanced Ceramics (Ed. R.W. Cahn), Pergamon, Oxford, Vol. 2(1990) 1111.
• 5-08.035V
  D. Holz, R. Janssen, K. Friedrich and N. Claussen: Abrasive Wear of Ceramic-Matrix Composites, J. Europ. Ceram. Soc.5 (1989) 229
• 5-08.036V
  E. Lutz and N. Claussen: R-Kurven- und Thermoschockverhalten von Duplex-Keramiken, DKG-Forschungsberichte 5, Heft 1 (1990) 9
• 5-08.037V
  N. Claussen: Herstellung keramischer Werkstoffe durch Schmelzoxidation, Handbuch der Technik, Vulkan-Verlag (1990) 523
• 5-08.039V
  N.A. Travitzky and N. Claussen: Chemical Stability of Cordierite-ZrO2 Composites, J. Europ. Ceram. Soc. 5 (1989) 327
• 5-08.040V
  M. Sindel, N.A. Travitzky and N. Claussen: Influence of MgAl2O3 on the Directed Oxidation of Molten Al Alloys, J. Am. Ceram. Soc. 73 (1990) 11
• 5-08.041V
  N. Claussen, N.A. Travitzky and Suxing Wu: Tailoring of Reaction-Bonded Al2O3 (RBAO) Ceramics, Ceram. Eng. Sci. Proc. Ceram. Eng. Sci. Proc. 11 (1990)806
• 5-08.042V
  A.J. Gesing, G. Burger, E. Luce, N. Claussen, Suxing Wu and N.A. Travitzky: Preparation and Characterization of RBAO-Matrix SiC Particulate FillerComposites, Ceram. Eng. Sci. Proc. 11 (1990) 821
• 5-08.045V
  M. Kulig, P. Greil: Surface Chemistry and Suspension Stability of Oxide-Nitride Powder Mixtures, J. Mat. Sci. 26 (1990) 216
• 5-08.047V
  H. Scholz, P. Greil: Nitridation Reactions of Molten Al-Si-Mg-Alloys, J. Mat. Sci. 26 (1991) 669
• 5-08.048V
  M. Seibold, P. Greil: Composite Ceramics from Polymer-Metal Mixtures, in: Advanced Materials and Processes 1, DGM Informationsgesellschaft, Oberursel(1990) 641
• 5-08.049V
  P. Greil: Thermodynamic Calculations of Fiber-Matrix Stability in Ceramic Matrix Composites, J. Europ. Ceram. Soc. 6 (1990) 53
• 5-08.050V
  H. Scholz, P. Greil: Synthesis of High Purity AlN by Nitridation of Li-doped Al-Melt, J. Europ. Ceram. Soc. 6 (1990) 237
• 5-08.051V
  N. Claussen: Ceramic Platelet Composites, Proc. 11th Riso Int. Sympos.Met. and Mat.Sci, Roskilde, Dänemark (1990)1
• 5-08.052V
  S. Wu, N.A. Travitzky, N. Claussen: Processing of Reaction-Bonded Al2O3 (RBAO) Composites, ibid. 529
• 5-08.055V
  E. Lutz, M.V. Swain, N. Claussen: Thermal Shock Behavior of Duplex Ceramics, J.Am.Ceram.Soc. 74 (1991) 19
• 5-08.056V
  E. Lutz, N. Claussen, M.V. Swain: KR-Curve Behavior of Duplex Ceramics, J.Am.Ceram.Soc. 74 (1991) 11
• 5-08.057V
  E. Lutz, N. Claussen: Duplex Ceramics: I. Stress Calculations, Fabrication and Microstructure, J.Europ.Ceram.Soc.7 (1991) 209; II: Strength and Toughness, ibid.219
• 5-08.058V
  S. Wu, A.J. Gesing, N.A. Travitzky, N. Claussen: Fabrication and Properties of Al-Infiltrated RBAO-Based Composites, J.Europ.Ceram.Soc. 7 (1991) 277
• 5-08.059V
  N. Claussen, S. Wu: Processing and Properties of Reaction-Bonded Al2O3 (RBAO) and Mullite Ceramics, Ceram.Trans., August 1991, to be published
• 5-08.060V
  N. Claussen, D. Holz, M. Rühle, S. Wu: Reaction-Bonded ZrO2-Toughened Al2O3 (RBAO, Proc.Mat.Soc. of Japan, 1991, to be published
• 5-08.061V
  C. Nischik, M. Seibold, N.A. Travitzky, N. Claussen: Effect of Processing Parameters on Mechanical Properties of Platelet-Reinforced Mullite Composites,J.Am.Ceram.Soc. 74 (1991) 2464
• 5-08.062V
  S. Wu und N. Claussen: "Fabrication and Properties of Low-Shrinkage Reaction-Bonded Mullite"; J. Am. Ceram. Soc. 74 [10] 2460-2463 (1991)
• 5-08.063V
  P. Greil, R. Nitzsche, H. Friedrich, W. Hermel: Evaluation of Oxygen Content on Silicon Nitride Powder Surface from the Measurement of the Isoelectric Point,J.Europ.Ceram.Soc. 7 (1991) 353
• 5-08.064V
  P. Greil, U. Gruber, N. Travitzky, M. Kulig: Pressure Filtration of Silicon Nitride Suspensions with Constant Filtration Rate, to be publ. in Mat.Sci.Eng. A (1992)
• 5-08.065V
  P. Greil: Surface Properties of Silicon Nitride Powders, to be publ. in: Colloid Chemistry and Rheology of Ceramics, edt. Tadros, (1992)
• 5-08.066V
  She Jihong, Jiang Dongliang, Peter Greil: Hot Isostatic Pressing of Presintered Silicon Carbide Ceramics, J.Europ.Ceram.Soc. 7 (1991) 243
• 5-08.067V
  D. Jiang, J. She, S. Tan, P. Greil: Strengthening of Silicon Carbide Ceramics by Surface Nitridation during Hot-Isostatic Pressing, subm. to J.Am.Ceram.Soc.(1992)
• 5-08.068V
  P. Greil, N. Claussen: Novel Processing and Properties of Platelet and Fiber Reinforced Composite Ceramics, to be publ. in Proc. Science of Engineering Ceramics'91, Koda/J. October 21-23 (1991)
• 5-08.069V
  P. Greil, M. Seibold: Active Filler Controlled Pyrolysis (AFCOP) - A Novel Fabrication Route to Ceramic Composite Materials, Ceramic Transactions Vol. 19,Advanced Composite Materials, edt. M.D. Sacks, The Am.Ceram.Soc., Westerville OH (1991) 43
• 5-08.070V
  P. Greil, M. Seibold: Modelling of Dimensional Change During Polymer-Ceramic Conversion for Bulk Component Fabrication, J.Mat.Sci. 27 (1992) 1053
• 5-08.071V
  M. Seibold, B. Ahlers, P. Greil: Plastic Forming of Polymer Metal Blends for the Fabrication of Ceramic Matrix Composites, Mat.Sci.Mon. 68,Adv.Struct.Inorg.Comp., edt. P. Vincencini, Elsevier, Amsterdam/NE (1991) 555
• 5-08.072V
  T. Erny, M. Seibold, O. Jarchow, P. Greil: Microstructure of Polymer Derived Oxycarbide Composites, subm. to J.Am.Cerm.Soc. (1992)
• 5-08.073V
  B. Ahlers, T. Erny, M. Kulig, A. Stark, M. Seibold, P. Greil: Ceramic Coatings via Reactive Metal Vapor Deposition on Carbon Containing Composites, to bepubl. in Proc. 2nd ECERS-Conference, Augusburg/GE (1991)
• 5-08.074V
  M. Seibold, P. Greil: Fabrication of Oxycarbide Composite Materials by Active Filler Controlled Pyrolysis (AFCOP) of Polysiloxane Precursors,J.Europ.Ceram.Soc. (1991) submitted
• 5-08.075V
  K.J. Hüttinger, P. Greil: Keramische Verbundwerkstoffe für Höchsttemperaturanwendungen, CFI/Ber.Dt.Keram.Ges. (1992) submitted
• 5-08.076V
  H. Prielipp, M. Geerken, J. Rödel and N. Claussen: Gas Pressure Metal Infiltration of Porous Ceramic Preforms, Proceedings 3rd Int. Conf. on Hot IsostaticPressing, Osaka (1991) in press
• 5-08.078V
  N. Claussen and J. Rödel: Strong and Tough Ceramic Composites, Proceedings Int. Symposium on Ceramics, Yokohama (1991) in press
• 5-08.079V
  J. Rödel: Crack Closure Forces in Ceramics: Characterization and Formation, J.Eur.Ceram.Soc. (1992) in press
• 5-08.080V
  J. Rödel: Interaction Between Crack Deflection and Crack Bridging, J.Eur.Ceram.Soc. (1991) submitted
• 5-08.081V
  F. Meschke, G. de Portu and N. Claussen: Microstructure and Thermal Stability of Fine-grained (Y, Mg)-PSZ Ceramics witgh Alumina Additions, J. Eur. Ceram.Soc. 11 (1993) 481-86
• 5-08.082V
  S. Wu, D. Holz, and N. Claussen: Mechanisms and Kinetics of Reaction-Bonded Aluminum Oxide Ceramics, J. Am. Ceram. Soc. 76 (1993) 970-80
• 5-08.083V
  D. Holz, S. Wu, S. Scheppokat, and N. Claussen: Effect of Processing Parameters on Phase and Microstructure Evolution in RBAO Ceramics, J. Am. Ceram. Soc.77 (1994) submittet
• 5-08.084V
  D. Holz, S. Wu, R. Janßen und N. Claussen: Das RBAO-Verfahren, DKG-Loseblattsammlung "Keramische Werkstoffe", Herausgeber J. Kriegesmann, Oktober1993, Kapitel 3.6.4.1, Seite 1-14
• 5-08.085V
  N. Claussen, S. Wu, and D. Holz: Reaction Bonding of Aluminum Oxide (RBAO) Composites: Processing, Reaction Mechanisms, and Properties, J. Eur. Ceram.Soc. 12 (1994) submitted
• 5-08.086V
  D. Holz, M. Geerken, S. Wu, R. Janßen and N. Claussen: HIP of Reaction-Bonded Alumina (RBAO) with Various Ratios of Open-to-Closed Porosity,Proceeding of HIP `93,, April 21-23, 1993, Antwerpen, Belgium, eds. L. Delaey, H. Tas, and W. Kaysser, Elsevier
• 5-08.087V
  D. Holz, M. Röger, R. Janßen, and N. Claussen: Mechanical Properties of Reaction-Bonded Al2O3 /ZrO2 Composites, Ceram. Eng. Sci. Proc. 15 (1994)submitted
• 5-08.088V
  N.A. Travitzky, N. Claussen und D.P.H. Hasselmann: Influence of Sintering Condidtions on Mechanical and Thermal Properties of Cordierite-ZrO2 Composites, J.Eur. Ceram. Soc. 9 (1992) 165-68
• 5-08.089V
  D.E. García, J. Rödel und N. Claussen: Subcritical Crack Growth and R-Curve Behaviour in Al2O3 -Toughened Y-TSP, in: Zirconia V (Eds.: S. Badwal, J.Bannister, R. Hannink) Technomic Publ. Lancastger (1993) 410-19
• 5-08.090V
  T. Claassen und N. Claussen: Processing Routes and Microstructures of Ceramic-Matrix/Platelet Composites, in: 4th int. Symp. on Ceramic Materials andComponents for Engines (Eds.: R. Carlsson et al.) Elsevier, London (1992) 712-25
• 5-08.091V
  T. Claassen und N. Claussen: Processing of Ceramic-Matgrix/Platelet Composites by Tape Casting and Lamination, J. Eur. Ceram. Soc., 10 (1992) 263-271
• 5-08.092V
  H. Prielipp, J. Rödel und N. Claussen: Metalle verbessern die Eigenschaften von Keramiken, Spektrum der Wissenschaften 1 (1992) 107-11
• 5-08.093V
  M.C. Knechtel, D.E. García, J. Rödel und N. Claussen: Subcritical Crack Growth in Y-TZP and Al2O3 -Toughened Y-TZP, J. Am. Ceram. Soc., 76 (10) (1993)2681-84
• 5-08.094V
  J. Rödel, M. Sindel, M. Dransmann, R.W. Steinbrech and N. Claussen: R-Curve Behavior in Ceramic Composites Produced by Directed Metal Oxidation, J. Eur.Ceram. Soc. 14 (1994) 153 - 61
• 5-08.095V
  S. Schön, H. Prielipp, R.Janssen, J. Rödel, and N. Claussen: Effect of Microstructural Scale on Thermal Shock Resistance of Metal-Reinforced Alumina, J. Am.Ceram. Soc. 77 (1994) 701 - 4
• 5-08.096V
  D.E. García, R. Janssen and N. Claussen: In situ-Reinforced RBAO, in: 3rd Euro-Ceramics, Vol. 3 (Eds.: P. Duran and J.F. Fernandez) Faenza Ed., San Vicente (1993) 719 - 24
• 5-08.097V
  Dietmar Holz, Suxing Wu, Sven Scheppokat and Nils Claussen"Effect of Processing Parameters on Phase and Microstructure Evolution in RBAOCeramics, J. Am.Ceram. Soc. 77 (1994) 2509 - 17
• 5-08.098V
  R. Janssen, S. Schön, H. Prielipp and N. Claussen: Multifunctional Ceramics for Thermal Shock Applications, in: Thermal Shock and Thermal Fatigue in AdvancedCeramics (Eds.: G.A. Schneider und G. Petzow) Kluwer Acad. Reb., Amsterdam (1993) 521 - 9
• 5-08.099V
  D. Hotza, R. Janssen, N. Claussen, P. Greil: Hydrophobic Aluminum Nitride Powder for Aqueous Tape Casting, Ceram. Trans. 51 (1995) 397 - 401
• 5-08.100V
  Chu-Wan Hong and Ulrich Weiss, Nils Claussen and Dierk G. Feldmann: A New Design of Monolithic Particle Filters with Transverse Isotropic Property for DieselMotors, SAE Special Tech Paper Ser. 940 462 SP 1020 (1994) 261 - 76
• 5-08.101V
  J. Seidel, N. Claussen and J. Rödel: Reliability of Alumina ceramics, I. Effect of Grain Size, J. Eur. Ceram. Soc. 15 (1995) 395 - 404
• 5-08.102V
  D.E. García, J. Wendorff, R. Janssen and N. Claussen: Formation of Needle-Like Grains in Al2O3, Ceram. Eng. Sci. Proc. 15 (1994) 669 - 76
• 5-08.103V
  J. Wendorff, D.E. García, R. Janssen and N. Claussen: Sapphire Fiber Reinforced RBAO, ibid. 364 - 70
• 5-08.104V
  D. Holz, M. Röger, R. Janssen and N. Claussen: Mechanical Properties of Reaction-Bonded Alumina Ceramics, ibid., 651 - 8
• 5-08.105V
  N. Claussen, S. Wu and D. Holz: Reaction Bonding of Aluminum Oxide (RBAO) Composites: Processing, Reaction Mechanisms and Properties, J. Eur. Ceram.Soc. 14 (1994) 97 - 109
• 5-08.106V
  D. Holz, S. Wu, R. Janssen, and N. Claussen: Das RBAO-Verfahren, in: Keramische Werkstoffe (Ed. J. Kriegesmann) DKG-Loseblattsammlg.Köln (1993) 1 - 14
• 5-08.107V
  S. Wu and N. Claussen: Reaction Bonding and Mechanical Properties of Mullite/Silicon Carbide Composites, J. Am. Ceram. Soc. 77 (1994) 2898 - 904
• 5-08.108V
  N. Claussen, M. Knechtel, H. Prielipp, J. Rödel: Metcers - A Strong Variant of Cermets, cfi/Ber. DKG 71 (1994) 301 - 4
• 5-08.109V
  C. von Minden, M.M.R. Boutz, S. Scheppokat, R. Janssen and N. Claussen: Superplastic Deformation of Zirconia/Alumina Composites Produced by ReactionBonding, in: Plastic Deformation of Ceramics, Plenum (1995) 333 - 41 (Eds.: R.C. Bradt, J. Routbort & C. Brookes)
• 5-08.110V
  F. Meschke, G. De Portu, and N. Claussen: Microstructure and Thermal Stability of Fine-Grained (Y, Mg)-PSZ Ceramics with Alumina Additions, J. Eur. Ceram.Soc. 11 (1993) 481 - 6
• 5-08.111V
  H. Prielipp, M. Knechtel, N. Claussen, S.K. Streiffer, H. Müllejans, M. Rühle and J. Rödel: Strength and Fracture Toughness of Aluminum/Alumina Compositeswith Interpenetrating Networks, Mat. Sci. and Eng. A, im Druck (1995)
• 5-08.112V
  M. Knechtel, H. Prielipp, H. Müllejans, N. Claussen and J. Rödel: Mechanical Properties of Al/Al2O3 and Cu/Al2O3 Composites with Interpenetrating Networks,Scr. Met. 31 (8) 1085 - 1090 (1994).
• 5-08.113V
  J. Rödel, H. Prielipp, N. Claussen, M. Sternitzke, K.B. Alexander, P.F. Becher and J.H. Schneibel: Ni3Al/Al2O3 Composites with Interpenetrating Networks, Scr.Metall. et Mater. (1995) 843 - 8
• 5-08.114V
  D. Holz, S. Pagel, C. Bowen, S. Wu and N. Claussen: Fabrication of Low-to-Zero Shrinkage Reaction-Bonded Mullite Composites, J.Eur.Ceram. Soc. 16 (1996)
• 5-08.115V
  F. Meschke, N. Claussen, G. de Portu, J. Rödel: Phase Stability of Fine-Grained (Mg, Y) - PSZ, J.Am.Ceram.Soc. 78 (1995) 1997 - 9
• 5-08.116V
  M. Hoffman, J. Rödel, B. Fiedler, H. Prielipp and N. Claussen: Toughening of Ceramics by Metal Fiber Reinforcement, in: Proc. of ICCM-10, Vancouver 1995
• 5-08.117V
  B. Fiedler, H. Prielipp, N. Claussen, M. Hoffman and J. Rödel: Effect of Metal Fiber Orientation on Toughening in Ceramic Matrix Compositeseingereicht bei Actametall. et mater.
• 5-08.118V
  M. Knechtel, H. Prielipp, J. Rödel und N. Claussen: Bruchzähigkeit, Bruchfestigkeit und Verläßlichkeit von metallverstärktem Al2O3, in: Hochleistungskeramiken(DFG) (Eds: G. Petzow, J. Tobolski and R. Telle) VCH Verlagsges. Weinheim (1995) 233 - 40
• 5-08.119V
  F. Meschke, N. Claussen, G. de Portu, J. Rödel: Interrelation Between Strength, Flaw Size, Transformability and R-Curve Behaviour, in: 4th Euro Ceramics, Vol. 3(Eds.: S. Meriani, V. Sergo) Faenza Ed., (1995) 161 - 168
• 5-08.120V
  M. Hoffman, B. Fiedler, U. Köpke, H. Prielipp, N. Claussen and J. Rödel. Toughening Mechanisms of Metal Fibre Reinforced Ceramics, in: Fracture Mechanics ofCeramics Vol. 11 und 12 (Eds.: D. Munz, et. al.)
• 5-08.121V
  D.E. Garcia, R. Janssen and N. Claussen: Fast Firing: Sintering Under High Thermal Gradients, ECerS 95 Riccione October 2 - 6, 1995
• 5-08.122V
  J. Seidel, N. Claussen and J. Rödel: Reliability of Alumina Ceramics II. Effect of Processing, J. Eur. Ceram. Soc. 16 (1996)
• 5-08.123V
  J. Wendorff, R. Janssen, and N. Claussen: The Fiber Push-Out Test at High Temperatures for Interface Characterization of Ceramic/Ceramic Composites, ECCMCTS, (1994) 69-74
• 5-08.124V
  R. Janssen, J. Wendorff, N. Claussen: Fiber Reinforcement of Reaction Bonded Oxide Ceramics, Ceram. Trans. 58 (1995) 167-73
• 5-08.125V
  J. Wendorff, R. Janßen und N. Claussen: Saphirfaserverstärktes Aluminiumoxid, in: Verbundwerkstofforschung (Eds.: J. Bossert, N. Claussen, R. Nitsche),Expertverlag, Renningen (1995) 206-16
• 5-08.126V
  Srinivasarao Lathabai, David G. Hay, Florian Wagner, and Nils Claussen: Reaction-Bonded Mullite/Zirconia Composites, J. Am. Ceram. Soc. 79 (1996)
• 5-08.127V
  O. Greis, R. Ziel, D.E Gracía, N. Claussen, B. Breidenstein, and A. Haase: Crystal Structure and Morphology of Disordered AlNbO4 from X-Ray PowderDiffraction, EPDIC IV, Proceedings in Materials Science Forum
• 5-08.128V
  N. Claussen, R. Janssen and D. Holz: Reaction Bonding of Aluminum Oxide (RBAO), J.Ceram.Soc.Jap. 103 (1995) 749 - 58
• 5-08.129V
  N. Claussen, M. Knechtel, H. Prielipp and J. Rödel: Ceramic-Metal Composites with Interpenetrating Networks, Ceram. Trans. 46 (1995) 595 - 9
• 5-08.130V
  M. Knechtel, N. Claussen and J. Rödel: Reliability of Structural Ceramics, Phil. Trans. R. Soc. Lond. A 351 (1995) 469 - 483
• 5-08.131V
  D.E. García, J. Wendorff, R. Janssen, N. Claussen: Fast Firing of Reaction-Bonded Aluminium Oxide RBAO Composites, J. Mat.Sci. 30 (1995) 5121 - 4
• 5-08.132V
  D.E. García, J. Seidel, R. Janssen and N. Claussen: Fast Firing of Alumina, J. Eur. Ceram. Soc. 15 (1995) 935 - 8
• 5-08.133V
  W.D. Kaplan, H. Müllejans, M. Rühle, J. Rödel and N. Claussen: Ca Segregation to Basal Surfaces in α-Alumina, J. Am. Ceram. Soc., 78 (1995) 2841- 4
• 5-08.134V
  S. Wu und N. Claussen: "Reaction Bonding and Mechanical Properties of Mullite/Silicon Carbide Composites"; J. Am. Ceram. Soc. 77 [11] 2898-2904 (1994)
• 5-08.135V
  D. Holz, S. Pagel, C. Bowen, S. Wu und N. Claussen: "Fabrication of Low-to-Zero Shrinkage Reaction Bonded Mullite Composites", J. Eur. Ceram. Soc. 16 [2] 255-260 (1996)
• 5-08.136V
  N. Claussen, D.E. Garcia and R. Janssen, Reaction Sintering of Alumina-Aluminide Alloys (3A), J. Mater. Res. 11 [11] (1996) 2884-2888
• 5-08.137V
  D.E. Garcia, J. Bruhn, S. Schicker, R. Janssen and N. Claussen, Alumina-Aluminide Alloys (3A), in: Advanced Synthesis and Processing of Composites and Advanced Ceramics II, edited by K.V. Logan, R. Spriggs and Z.A. Munir, The Am. Ceram. Soc., Westerville 1996, 219-230
• 5-08.138V
  D.E. Garcia, S. Schicker, J. Bruhn, R. Janssen and R. Claussen, Synthesis of Novel Niobium Aluminide-Based Composites, J. Am. Ceram. Soc. 80 [9] (1997) 2248-2252
• 5-08.139V
  S. Schicker, D.E. Garcia, J. Bruhn, R. janssen and N. Claussen, Reaction Processing of Al2O3 Composites Containing Iron and Iron Aluminides, J. Am. Ceram. Soc. 80 [9] (1997) 2294-2300
• 5-08.140V
  D.E. Garcia, S. Schicker, R. Janssen and N. Claussen, Nb- and Cr-Al2O3 Composites with Interpenetrating Networks, J. Eur. Ceram. Soc. 18 (1998) 601-605
• 5-08.141V
  D.E. Garcia, S. Schicker, J. Bruhn, R. Janssen and N. Claussen, Processing and Mechanical Properties of Presureless-Sintered Nb-Al2O3-Matrix Composites, J. Am. Ceram. Soc. 81 [2] (1998) 429-433
• 5-08.142V
  S. Schicker, D.E. Garcia, J. Bruhn, R. Janssen and N. Claussen, Reaction Synthesized Al2O3-Based Intermetallic Composites, Acta Mater. 46 [7] (1998) 2485-2492
• 5-08.143V
  F. Wagner, D.E. Garcia, A. Krupp and N. Claussen, Interpenetrating Al2O3-Aluminide Alloys Produced by Reaction Infiltration, submitted to J. Eur. Ceram. Soc. (1998)